Functionalized Hybrid Coatings on ABS Surfaces by PLD and Dip Coatings

It is important to give water-repellent and antibacterial properties to the acrylonitrile butadiene styrene (ABS) surfaces of the hearing aids. In this study, the sol–gel Si and sol–gel Ti solutions were prepared from the reactions of silicon ethoxide, titanium butoxide and methacrylic acid. The catalyst and Dynasylan F8815 were added to the sol–gel solutions to give hydrophobic properties onto the ABS surfaces. Additionally, silver nanoparticles were synthesized by nanosecond laser and added to the coating solutions to give extra antibacterial properties. The surfaces of the ABS targets were coated using the sol–gel dip coating and pulsed laser deposition techniques. The coatings with good adhesion between film and substrate and good water-repellent properties were achieved. The average contact angles for the coated ABS surfaces were measured in the range between 120 and 125 degrees. The obtained sol–gel materials and produced thin films onto the ABS surfaces were also analyzed in terms of the antibacterial properties. The highly antibacterial properties were observed in the sol–gel solutions and the thin films.     

POSS-based hybrid thermosets via photoinduced copper-catalyzed azide–alkyne cycloaddition click chemistry

An efficient approach for the preparation of inorganic/organic hybrid thermosets via photoinduced copper-catalyzed azide–alkyne cycloaddition click chemistry is established. Highly cross-linked thermoset polymers have been practically obtained by this technique using multifunctional compounds, tri-alkyne (1,1,1-tris[4-(2-propynyloxy) phenyl]-ethane) with octakis-azido-POSS or tri-azide (3,3′-((2-((3-azido-2-hydroxypropoxy)methyl)-2-ethylpropane-1,3-diyl)bis(oxy))bis(1-azidopropan-2-ol)) in the presence of Cu(II)Br₂/N,N,N′,N″,N?-pentamethyldiethylenetriamine/2-dimethoxy-2-phenyl acetophenone. The homogeneously distributed POSS nanoparticles are clearly detected in the TEM micrographs; whereas the TGA analysis shows that the obtained hybrid thermosets are thermally stable up to 360 °C and begin to lose weight at higher temperatures with a char yield of 23–50% at 800 °C.     

Composition dependences of thermodynamical properties associated with Pb-free ternary,quaternary, and quinary solder systems

In the present study, Chou’s General Solution Model (GSM) has been used to predict the enthalpy and partial enthalpies of mixing of the liquid Ag–In–Sn ternary, Ag–In–Sn–Zn quaternary, and Ag–Au–In–Sn–Zn quinary systems. These are of technical importance to optimize lead-free solder alloys, in selected cross-sections: x_In/x_Sn = 0.5/0.5 (ternary), Au–In_0.1–Sn_0.8–Zn_0.1, Ag–In_0.1–Sn_0.8–Zn_0.1 (quaternary), and t = x_Au/x_In = 1, x_In = x_Sn = x_Zn (quinary) at 1173, 773, and 773 K, respectively. Moreover, the activity of In content in the ternary alloy system Ag–In–Sn has been calculated and its result is compared with that determined from the experiment, while the activities of Ag contents associated with the alloys mentioned above have been calculated. The other traditional models such as of Colinet, Kohler, Muggianu, Toop, and Hillert are also included in calculations. Comparing those calculated from the proposed GSM with those determined from experimental measurements, it is seen that this model becomes considerably realistic in computerization for estimating thermodynamic properties in multicomponent systems.     

Synthesis and spectroelectrochemistry of dithieno(3,2‐b:2′,3′‐d)pyrrole derivatives

New π‐conjugated polymers containing dithieno(3,2‐b:2′,3′‐d)pyrrole (DTP) were successfully synthesized via electropolymerization. The effect of structural differences on the electrochemical and optoelectronic properties of the 4‐[4H‐dithieno(3,2‐b:2′,3′‐d)pyrrol‐4‐yl]aniline (DTP–aryl–NH₂), 10‐[4H‐dithiyeno(3,2‐b:2′,3′‐d)pirol‐4‐il]dekan‐1‐amine (DTP–alkyl–NH₂), and 1,10‐bis[4H‐dithieno(3,2‐b:2′,3′‐d)pyrrol‐4‐yl] decane (DTP–alkyl–DTP) were investigated. The corresponding polymers were characterized by cyclic voltammetry, NMR (¹H‐NMR and ¹³C‐NMR), and ultraviolet–visible spectroscopy. Changes in the electronic nature of the functional groups led to variations in the electrochemical properties of the π‐conjugated systems. The electroactive polymer films revealed redox couples and exhibited electrochromic behavior. The replacement of the DTP–alkyl–DTP unit with DTP–aryl–NH₂ and DTP–alkyl–NH₂ resulted in a lower oxidation potential. Both the poly(10‐(4H‐Dithiyeno[3,2‐b:2′,3′‐d]pirol‐4‐il)dekan‐1‐amin) (poly(DTP–alkyl–NH₂)) and poly(1,10‐bis(4H‐dithieno[3,2‐b:2′,3′‐d]pyrrol‐4‐yl) decane) (poly(DTP–alkyl–DTP)) films showed multicolor electrochromism and also fast switching times (<1 s) in the visible and near infrared regions. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40701.     

Quinoxaline derivatives as long wavelength photosensitizers in photoinitiated cationic polymerization of diaryliodonium salts

The present paper is focused on visible light initiated cationic polymerizations. Photoinitiated polymerization of representative vinyl ether and oxirane monomers using two quinoxaline derivatives; namely (2-(2,3-dihydrobenzo [b][1,4]dioxin-6-yl)-3-(2,3-dihydrobenzo[b]-[1,4]dioxin-7-yl)-5-(2,3-dihydrothieno[3,4-b][1,4]dioxin-5-yl)-8-(2,3-dihydrothieno[3,4-b][1,4]dioxin-7yl) quinoxaline) (DBQEd) and 2,3,5,8-tetra(thiophen-2-yl)quinoxaline (TTQ) are studied. Novel dyes based on the quinoxaline skeleton are employed as efficient photosensitizers in cationic photopolymerizations. Polymerizations were initiated at room temperature upon irradiation with long-wavelength UV and visible lights in the presence of diphenyliodonium hexafluorophosphate (Ph₂I⁺PF₆^?). The progress of the polymerizations was monitored by optical pyrometry (OP). Solar irradiation is also employed to carry out the cationic polymerization of a diepoxide monomer in the presence of air.     

Estimated anthropometric measurements of Turkish adults and effects of age and geographical regions

The purpose of this paper is to estimate the anthropometric characteristics of the Turkish population by geographical region, age and gender. A survey of 4205 samples consisting of 2263 male and 1942 female civilian subjects was done in the year of 2007. It contains data from all seven geographical regions of Turkey and from all age groups. In the study, height and weight of the subjects were measured by age. Then, these data were used for estimating anthropometric measurements of the Turkish population. The main result of this study is the anthropometric measurements table for Turkey which shows 37 measurements that are commonly used in industry. The anthropometric measurements that are used to make the designs fit human shape and the human/machine or human/environment interface should be updated through time due to changing body types over time (secular trends) due to numerous factors. In this study, we not only update these variables, which are 30 years old, but also investigate the age and region effects on stature and weight of Turkish population.Relevance to industry: During the design phase of a product, incorporating anthropometric information would yield more efficient designs, which are more user friendly, safer and enable higher performance and productivity. So the anthropometric measurements table that is extracted from this study can be used by industry to produce better human oriented products for Turkish population.     

Assessment of odorous VOCs released from a main MSW landfill site in Istanbul-Turkey via a modelling approach

An air pollution modeling study was conducted to investigate the odorous effects of volatile organic compounds (VOCs) emissions from a sanitary landfill area on ambient air quality. The atmospheric dispersion of hydrogen sulfide (H₂S) and 22 VOCs was modeled. Industrial Source Complex v3 Short Term (ISCST3) model was used to estimate hourly concentrations of odorous VOCs over the nearest residential area. Odor thresholds of VOCs of interest were also found in the literature. Results showed that short-term averages of three odorous VOCs, namely ethyl mercaptan, methyl mercaptan and hydrogen sulfide, exceeded their odor thresholds, which are reported to be 0.022, 0.138 and 11.1 μg/m³, respectively, at several points within the domain. Their highest concentrations within Gokturk County were estimated to be 0.09387 μg/m³ for ethyl mercaptan, 0.07934 μg/m³ for methyl mercaptan and 6.315 μg/m³ for hydrogen sulfide. Short-term model results revealed the occasional odor problems being reported for Gokturk County. Hourly concentrations were used to obtain frequencies of odor episodes in Gokturk County via a probability analysis. The results showed that ethyl mercaptan concentrations did not exceed its odor threshold during more than 8.84% of the time. Similarly, the maximum odor episode frequencies for methyl mercaptan and hydrogen sulfide were 0.98% and 0.34% of the time, respectively.     

Tribological Characteristics of Calophyllum inophyllum–Based TMP (Trimethylolpropane) Ester as Energy-Saving and Biodegradable Lubricant

The purpose of this research is an experimental study of Calophyllum inophyllum (CI)-based trymethylolpropane (TMP) ester as an energy-saving and biodegradable lubricant and compare it with commercial lubricant and paraffin mineral oil using a four-ball tribometer. CI-based TMP ester is a renewable lubricant that is nonedible, biodegradable, and nontoxic and has net zero greenhouse gases. The TMP ester was produced from CI oil, which has high lubricity properties such as higher density, higher viscosity at both 40°C and 100°C and higher viscosity index (VI). Experiments were conducted during 3,600 s with constant load of 40 kg and constant sliding speed of 1,200 rpm at temperatures of 50, 60, 70, 80, 90, and 100°C for all three types of lubricant. The results show that CI TMP ester had the lowest coefficient of friction (COF) as well as lower consumption of energy at all test temperatures, but the worn surface roughness average (R_a) and wear scar diameter were higher compared to paraffin mineral oil and commercial lubricant. Before 80°C, CI TMP ester actually has a higher flash temperature parameter (FTP) than paraffin mineral oil and as the temperature increases, the FTP of TMP ester decreases. The worn surfaces of the stationary balls were analyzed by scanning electron microscopy (SEM) and results show that CI TMP ester has the highest wear compared to paraffin mineral oil and lowest wear compared to commercial lubricant. However, CI TMP ester is environmentally desired, competitive to commercial lubricant, and its use should be encouraged.